Removal of Fe and Mn from the groundwater by using zeolite with Rossellomorea sp.

Groundwater is one of the alternatives to surface water that can be used for drinking water; however, it normally exists with high iron and manganese content. In this study, a column study was conducted to observe the elimination of iron (Fe) and manganese (Mn) in the groundwater under different retention times by using zeolite immobilized with iron-oxidizing bacteria (IOB). Rossellomorea sp., representing an IOB, was found from the isolation process and was further cultured in the laboratory for immobilization into the natural zeolite as replacement materials for the sand filter. When the zeolite assisted with the Rossellomorea sp. was used, the elimination of Fe and Mn were 99.34% and 88.92%, respectively, compared to the removal of Fe and Mn, which were 93.62% and 93.73%, respectively, for media without immobilization. The presence of Rossellomorea sp. enhances the Fe oxidation, resulting in high removal of Fe. The Thomas and Yoon-Nelson models were performed in both raw zeolite and zeolite with IOB. The total coliform (most probable number [MPN]) increased from 70.8 to 307.6 MPN/100 mL because of the Rossellomorea sp. present that promotes the growth of coliform bacteria. In conclusion, the immobilization of zeolite with IOB is a potential technique to extract the Fe and Mn in the groundwater. PRACTITIONER POINTS: Zeolite incorporated with Rossellomorea sp. has higher removal performance of Fe, whereas the removal of Mn reduced compared to the raw zeolite. The presence of Rossellomorea sp. enhances the oxidation of ferrous iron and improves the removal of Fe in the groundwater because the ferric iron is the priority ion to be exchanged. The removal of UV254 increase when Rossellomorea sp. present in the zeolite because the Rossellomorea sp. consume the natural organic matter as carbon source.

Kinetic evaluation of sonicated food waste in continuously stirred tank reactor.

This work aimed to evaluate the process performance and stability of the anaerobic digestion of sonicated food waste (SFW) by determining the kinetic parameters using Monod, Contois, Modified Stover-Kincannon, and Grau second-order multicomponent substrate removal kinetic models. The anaerobic digestion was conducted on the sonicated food waste (SFW) in a 13 L continuously stirred tank reactor (CSTR) with a stepwise organic loading rate (OLR) ranging from 1.5 to 3.5 gCOD/L.day. The experimental works were carried out in two stages (start-up then followed by semi-continuous). The ultrasonic pretreatment was performed by sonicating the food waste slurry for 10 minutes at a 20 kHz frequency and specific energy input of 25,997 kJ/kg TS. The process performance, as well as acceptable stability in the SFW digester, provided satisfactory predictions with Monod, Modified Stover-Kincannon, Grau second-order multicomponent substrate removal, and Contois kinetic models. A significant relationship was seen between the predicted and experimental data with correlation coefficients (R2) ranging from 0.893 to 0.996. In this study, the Monod model with R2 = 0.996 indicates the most suitable model for understanding the kinetic parameters of the anaerobic system in the CSTR which digests the sonicated food waste (SFW) slurry.

Insights into the Role of Biopolymer-Based Xerogels in Biomedical Applications.

Xerogels are advanced, functional, porous materials consisting of ambient, dried, cross-linked polymeric networks. They possess characteristics such as high porosity, great surface area, and an affordable preparation route; they can be prepared from several organic and inorganic precursors for numerous applications. Owing to their desired properties, these materials were found to be suitable for several medical and biomedical applications; the high drug-loading capacity of xerogels and their ability to maintain sustained drug release make them highly desirable for drug delivery applications. As biopolymers and chemical-free materials, they have been also utilized in tissue engineering and regenerative medicine due to their high biocompatibility, non-immunogenicity, and non-cytotoxicity. Biopolymers have the ability to interact, cross-link, and/or trap several active agents, such as antibiotic or natural antimicrobial substances, which is useful in wound dressing and healing applications, and they can also be used to trap antibodies, enzymes, and cells for biosensing and monitoring applications. This review presents, for the first time, an introduction to biopolymeric xerogels, their fabrication approach, and their properties. We present the biological properties that make these materials suitable for many biomedical applications and discuss the most recent works regarding their applications, including drug delivery, wound healing and dressing, tissue scaffolding, and biosensing.

Municipal Landfill Leachate Treatment and Sustainable Ethanol Production: A Biogreen Technology Approach.

Sustainable material sources are an important agenda to protect the environment and to meet human needs. In this study, Scenedesmus sp. was used to treat municipal landfill leachate via batch and continuous cultivation modes to protect the environment and explore sufficient biomass production for bioethanol production using Saccharomyces cerevisiae. Physicochemical characteristics of leachate were determined for the phases before, during, and after the process. Batch and continuous cultivation were used to treat raw leachate to determine optimum conditions for treatment. Then, the biomass of Scenedesmus sp. with and without sonication was used as a substrate for ethanol production. Sonication was carried out for biomass cell disruption for 20 min at a frequency of 40 kHz. Through batch cultivation mode, it was found that pH 7 was the optimum condition for leachate treatment. Continuous cultivation mode had the highest removal values for COD, phosphorus, and carbohydrate, namely 82.81%, 79.70%, and 84.35%, respectively, among other modes. As for ethanol production, biomass without sonication with 9.026 mg·L-1 ethanol, a biomass concentration of 3.300 µg·L-1, and pH 5 were higher than biomass with sonication with 5.562 mg·L-1 ethanol, a biomass concentration of 0.110 µg·L-1, and pH 5. Therefore, it is evident that the leachate has the potential to be treated by Scenedesmus sp. and converted to bioethanol in line with the concept of sustainable materials.

Optimisation of self-healing of bio-foamed concrete bricks pores using Bacillus tequilensis under different temperature and CO2 curing conditions.

The self-healing of bio-concrete cracks and pores have been utilised worldwide to improve the properties of bio-concrete using different types of bacteria. Meanwhile, no published research was conducted to heal bio-foamed concrete bricks (B-FCB) pores using Bacillus tequilensis. Previous studies focused on the concentration of bacteria and neglect other factors that could affect the healing process. This research aimed to optimise the healing ratio of B-FCB pores using four factors: B. tequilensis concentration, concrete density, temperature and CO2 concentration. Initial water absorption (IWA) and water absorption (WA) were used as responses in statistical methods, namely, factorial and response surface methodology (RSM). B. tequilensis species was isolated from cement kiln dust, produced in a powder form, then subjected to simulate test using a special medium consisting of foamed concrete materials to check the survival ability in B-FCB. SEM, EDX, and XRD were used to investigate the healing process of B-FCB pores. The results revealed that the decrement ratios of IWA and WA of B-FCB were 52.8% and 29.1% compared to FCB, respectively. SEM results reflect the healing that occurred in B-FCB pores, mostly healed via precipitation of CaCO3 as demonstrated on the XRD results.

Optimization of mixing ratio, shaking speed, contact time, and pH on reduction of Chemical Oxygen Demand (COD) and Ammoniacal Nitrogen (NH3-N) in leachate treatment.

When the inevitable generation of waste is considered as hazardous to health, damaging ecosystem to our environment, it is important to develop an innovative technologies to remediate pollutant sources for the safety and environmental protection. The development of adsorption technique for the reduction of extremely effective pollutants in this regard. Green mussel and zeolite mixing media were investigated for the reduction of the concentration of organic constituents (COD) and ammoniacal nitrogen from leachate. The leachate treatability was analyzed under various stages of treatment parameter, namely mixing ratio, shaking speed, contact time, and pH. Both adsorbent were sieve values in between 2.00-3.35 mm particle size. The optimum pH, shaking speed, contact time, and mixing ratio were determined. Leachate samples were collected from influent untreated detention pond at Simpang Renggam landfill site in Johor, Malaysia. The result of leachate characterization properties revealed that non-biodegradability leachate with higher concentrations of COD (1829 mg/L), ammoniacal nitrogen (406.68 mg/L) and biodegradability value (0.08) respectively. The optimal reduction condition of COD and ammoniacal nitrogen was obtained at 200 rpm shaken speed, 120 minute shaken time, optimum green mussel and zeolite mix ratio was 2.0:2.0, and pH 7. The isothermic study of adsorption shows that Langmuir is best suited for experimental results in terms of Freundlich model. The mixing media also provided promising results to treating leachate. This would be greatly applicable in conventionally minimizing zeolite use and thereby lowering the operating cost of leachate treatment.Implications: The concentration of organic constituents (COD) and ammoniacal nitrogen in stabilized landfill leachate have significant strong influences of human health and environmental. The combination of mixing media green mussel and zeolite adsorbent COD and ammoniacal nitrogen reduction efficiency from leachate. This would be greatly applicable in future research era as well as conventionally minimizing high cost materials like zeolite use and thereby lowering the operating cost of leachate treatment.

Adsorption of Zn2+ from Synthetic Wastewater Using Dried Watermelon Rind (D-WMR): An Overview of Nonlinear and Linear Regression and Error Analysis.

Sustainable wastewater treatment is one of the biggest issues of the 21st century. Metals such as Zn2+ have been released into the environment due to rapid industrial development. In this study, dried watermelon rind (D-WMR) is used as a low-cost adsorption material to assess natural adsorbents' ability to remove Zn2+ from synthetic wastewater. D-WMR was characterized using scanning electron microscope (SEM) and X-ray fluorescence (XRF). According to the results of the analysis, the D-WMR has two colours, white and black, and a significant concentration of mesoporous silica (83.70%). Moreover, after three hours of contact time in a synthetic solution with 400 mg/L Zn2+ concentration at pH 8 and 30 to 40 °C, the highest adsorption capacity of Zn2+ onto 1.5 g D-WMR adsorbent dose with 150 µm particle size was 25 mg/g. The experimental equilibrium data of Zn2+ onto D-WMR was utilized to compare nonlinear and linear isotherm and kinetics models for parameter determination. The best models for fitting equilibrium data were nonlinear Langmuir and pseudo-second models with lower error functions. Consequently, the potential use of D-WMR as a natural adsorbent for Zn2+ removal was highlighted, and error analysis indicated that nonlinear models best explain the adsorption data.

Optimization of Bio-Foamed Concrete Brick Strength via Bacteria Based Self-Healing and Bio-Sequestration of CO2.

This research aimed to optimize the compressive strength of bio-foamed concrete brick (B-FCB) via a combination of the natural sequestration of CO2 and the bio-reaction of B. tequilensis enzymes. The experiments were guided by two optimization methods, namely, 2k factorial and response surface methodology (RSM). The 2k factorial analysis was carried out to screen the important factors; then, RSM analysis was performed to optimize the compressive strength of B-FCB. Four factors, namely, density (D), B. tequilensis concentration (B), temperature (T), and CO2 concentration, were selectively varied during the study. The optimum compressive strength of B-FCB was 8.22 MPa, as deduced from the following conditions: 10% CO2, 3 × 107 cell/mL of B, 27 °C of T and 1800 kg/m3 of D after 28 days. The use of B. tequilensis in B-FCB improved the compressive strength by 35.5% compared to the foamed concrete brick (FCB) after 28 days. A microstructure analysis by scanning electronic microscopy (SEM), energy dispersive X-ray (EDX) and X-ray diffraction analysis (XRD) reflected the changes in chemical element levels and calcium carbonate (CaCO3) precipitation in the B-FCB pores. This was due to the B. tequilensis surface reactions of carbonic anhydrase (CA) and urease enzyme with calcium in cement and sequestered CO2 during the curing time.

A Review on Bacterial Contribution to Lignocellulose Breakdown into Useful Bio-Products.

Discovering novel bacterial strains might be the link to unlocking the value in lignocellulosic bio-refinery as we strive to find alternative and cleaner sources of energy. Bacteria display promise in lignocellulolytic breakdown because of their innate ability to adapt and grow under both optimum and extreme conditions. This versatility of bacterial strains is being harnessed, with qualities like adapting to various temperature, aero tolerance, and nutrient availability driving the use of bacteria in bio-refinery studies. Their flexible nature holds exciting promise in biotechnology, but despite recent pointers to a greener edge in the pretreatment of lignocellulose biomass and lignocellulose-driven bioconversion to value-added products, the cost of adoption and subsequent scaling up industrially still pose challenges to their adoption. However, recent studies have seen the use of co-culture, co-digestion, and bioengineering to overcome identified setbacks to using bacterial strains to breakdown lignocellulose into its major polymers and then to useful products ranging from ethanol, enzymes, biodiesel, bioflocculants, and many others. In this review, research on bacteria involved in lignocellulose breakdown is reviewed and summarized to provide background for further research. Future perspectives are explored as bacteria have a role to play in the adoption of greener energy alternatives using lignocellulosic biomass.

Elucidation of Mechanical, Physical, Chemical and Thermal Properties of Microbial Composite Films by Integrating Sodium Alginate with Bacillus subtilis sp.

Materials are the foundation in human development for improving human standards of life. This research aimed to develop microbial composite films by integrating sodium alginate with Bacillus subtilis. Sodium alginate film was fabricated as control. The microbial composite films were fabricated by integrating 0.1, 0.2, 0.3, 0.4, 0.5 and 0.6 g of Bacillus subtilis into the sodium alginate. Evaluations were performed on the mechanical, physical, chemical and thermal properties of the films. It was found that films reinforced with Bacillus subtilis significantly improved all the mentioned properties. Results show that 0.5 g microbial composite films had the highest tensile strength, breaking strain and toughness, which were 0.858 MPa, 87.406% and 0.045 MJ/m3, respectively. The thickness of the film was 1.057 mm. White light opacity, black light opacity and brightness values were 13.65%, 40.55% and 8.19%, respectively. It also had the highest conductivity, which was 37 mV, while its water absorption ability was 300.93%. Furthermore, it had a higher melting point of 218.94 °C and higher decomposition temperature of 252.69 °C. SEM also showed that it had filled cross-sectional structure and smoother surface compared to the sodium alginate film. Additionally, FTIR showed that 0.5 g microbial composite films possessed more functional groups at 800 and 662 cm-1 wavenumbers that referred to C-C, C-OH, C-H ring and side group vibrations and C-OH out-of-plane bending, respectively, which contributed to the stronger bonds in the microbial composite film. Initial conclusions depict the potential of Bacillus subtilis to be used as reinforcing material in the development of microbial composite films, which also have the prospect to be used in electronic applications. This is due to the conductivity of the films increasing as Bacillus subtilis cell mass increases.

Bacterial Diversity and Community Structure of a Municipal Solid Waste Landfill: A Source of Lignocellulolytic Potential.

Omics have given rise to research on sparsely studied microbial communities such as the landfill, lignocellulolytic microorganisms and enzymes. The bacterial diversity of Municipal Solid Waste sediments was determined using the illumina MiSeq system after DNA extraction and Polymerase chain reactions. Data analysis was used to determine the community's richness, diversity, and correlation with environmental factors. Physicochemical studies revealed sites with mesophilic and thermophilic temperature ranges and a mixture of acidic and alkaline pH values. Temperature and moisture content showed the highest correlation with the bacteria community. The bacterial analysis of the community DNA revealed 357,030 effective sequences and 1891 operational taxonomic units (OTUs) assigned. Forty phyla were found, with the dominant phyla Proteobacteria, Firmicutes, Actinobacteria, and Bacteroidota, while Aerococcus, Stenotrophomonas, and Sporosarcina were the dominant species. PICRUSt provided insight on community's metabolic function, which was narrowed down to search for lignocellulolytic enzymes' function. Cellulase, xylanase, esterase, and peroxidase were gene functions inferred from the data. This article reports on the first phylogenetic analysis of the Pulau Burung landfill bacterial community. These results will help to improve the understanding of organisms dominant in the landfill and the corresponding enzymes that contribute to lignocellulose breakdown.